Principal Dimensions

Construction
Epoxy/E-Glass/Foam/Balsa composite
Wet Pre-Preg, post cured in oven
Keel, mast support structure: Aluminium Grid
Keel: Cast iron fin, Lead Bulb, Epoxy Coated

Mechanical
Diesel engine: Yanmar Sail drive 3GMSD30
Two bladed geared folding propeller
Fuel tank: 75 litre aluminium
Fuel filter & water separator
Single lever throttle & gear control
Fuel Gauge
Waterlock with silencer

Electrical
12 volt DC distribution panel
Battery Condition meter
Circuit Breakers of appropriate amperage
Main battery switch
Batteries: 2 x 105 Amp hour
Alternator, 80 Amp on engine
ORC approved navigation lights
Red & White dome lights for general illumination
Halogen reading lights

Plumbing & Stove
Water tanks: 2 x 80 litre
pressurised water system
Galley sink with overboard drain
Vanity sink with overboard drain
Manual bilge pumps:
1 Cockpit, 1 Below Deck
Marine head c/w holding tank and overboard discharge
Flush seacocks on all openings below DWL
Fresh water fill below deck
Ice box
Stove: custom 3-burner Butane

Deck Hardware
Winches:

Primaries: Harken 48/3 Speed (2) OR Lewmar 48/3OR
Halyard: Harken 44/2 Speed (2) OR Lewmar 44STOR
Mainsheet: Harken 44/2 Speed (2) OR Lewmar 44STOR
Backstay: Hydraulic
Winch Handles: 10" Double Grip lock (2)
10" Single Grip lock (2)

Pulpits: S/s custom bow & stern rails with lights
Stanchions: 6 tapered, 4 tapered with braces
Stanchion bases: Custom flush fit
Lifelines: Upper & Lower 1 x 19 s/s wire
Rope clutches for halyards and pole lift (5)
Jib tracks, Fully adjustable with underdeck control lines
Barberhaul system 10:1
Cunningham lead aft to mainsheet trimmer
Outhaul led aft to mainsheet trimmer
Mainsheet along the boom 'European' style, lead under deck
Spinnaker Foreguy
Foredeck Hatch: 24" diameter, round alloy
Cockpit hatches: 5 x 12 (2)

Steering
Carbon rudder stock with Epoxy/Carbon/E-Glass Blade
Upper and lower roller bearings
Custom alloy tiller (standard)
Tiller extension
Wheel steering (optional)

Spars & Rigging
Custom carbon rig:
     Two sets swept aft spreader
     Custom hydraulic mast step
     Integrally moulded deck collar
     Roller bearing Spinnaker pole track
Aluminium boom: Outhaul, Lock offs for reef lines (2)
Vang: Solid strut lead aft port & stbd
Carbon spinnaker pole
Standing rigging: discontinuous rod
Permanent backstay: Kevlar to hydraulic cylinder
Tuff Luff headsail system

Running Rigging:
Main Halyard (1)
Forward Halyards (3)
Mainsheet (1)
Outhaul (1)
Cunningham (1)
Traveller Control (2)
Jib Sheet (2)
Jib In-haul (2)
Jib Car adjust (2)
Spin sheet (2)
Afterguy (2)
Foreguy (2:1) (1)
Backstay strop (1)
Spinnaker twing lines (2)

Miscellaneous
Exterior finish: Light colour gel coat on topsides & deck:
Double bootstripe is standard
Clear epoxy on bottom ready to sand & paint
Foils are epoxy coated & faired to template
Interior is finished in matte white paint
Four fixed berths: 4" cushions
Fabric covers on hanging lockers

One Design
Guaranteed to comply with Farr 40 One Design Class Rules on delivery